I am trying to create network between two nodes by following
I took TWO W72230F1(EFR32MG12 2.4GHz mesh networking kit) of 19db. then I programed the flash to device from (ot-cli-ftd.s37) for the device and flash proagmmer from tool by browsing the dummby bootloader file and i programmed it.
later i followed and did same process for the another device also flash to device fom(ot-cli-ftd.s37) and flashing a bootloader from tool dialog.
then now i am trying create network between them two devices. so for that i open LANUCH CONSOLE from the one device then i given command as below:
>dataset init new
>dataset commit active
after that i am getting this type error which i mentioned below:
>dataset init new
Error35: Invalid Command
i tryed this command from serial 0 and serial 1 from the both device even also i getting same error. i cant able to create the nework between the nodes.
i want to create the create between the node and later i want to there bandwidth for how long they communicate is possible.
I attach the image of my error. please find thye attachment.
But for now i cant able to create the network between them please help me regarding this. thanking you in advance.
I am using the EFR32MG12 (BRD 4161 Rev 03) as coordinator.
In the Network with Coordinator i have many different types of 3rd party devices (routers). I want to get the Battery Information of the 3rd party devices from the 3rd party device to Coordinator.
Now i am getting Sender Node id and Payload etc, but how to get the information about the Battery of 3rd party device to coordinator CLI.
please let know, thanking you.
When I set the pin of the GPIO to pull-up mode，Output is high.The voltage of GPIO is about 1.65V measured by voltmeter. In this GPIO suspension state, when I read the state of the pin through GPIO_PinInGet(gpioPortB,0) , I found that the result was 0.
In theory, I think when I set the output to high, the result should be 1, but I found that when I connected the pin to 3.3V, the result became 1, and when I disconnected the pin from 3.3V, the readout result was 1, not 0, so it seemed that the state of the PIN had something to do with its last state.
My device type is EFR32MG21 ，the SDK is EmberZNet 188.8.131.52.
MEMCOPY(emAfZclBuffer, zclBuffer , len);
*emAfResponseLengthPtr = len;
emAfCommandApsFrame->clusterId = clusterId;
emAfCommandApsFrame->options = EMBER_AF_DEFAULT_APS_OPTIONS;
emAfCommandApsFrame->sourceEndpoint = 1;
emAfCommandApsFrame->destinationEndpoint = 1;
emAfCommandApsFrame->profileId = 0x0104;
status = emberAfSendCommandUnicast(EMBER_OUTGOING_DIRECT, 0x0000);
Where is the fault?
I completed the first part of the Zigbee Boot Camp https://github.com/SiliconLabs/IoT-Developer-Boot-Camp/wiki/Zigbee-Boot-Camp
creating the light. Everything compiles and loads on my EFR32MG21 board. One of the final steps is to open the open the console, switch to "Serial 1" and press "Enter." You should see the project name. All I get is a carriage return. Serial 0 returns: "E[35005C24h]: No valid RTT block found. Please verify target application." And the Admin console is the WSTK prompt and appears to be working. I checked the GPIO pins and they looked correct. Below is what I think is the relevant section of the hwconf file.
Any thoughts would be helpful.
In hwconf: Serial section: Serial & Virtual COM port are checked
Port for application serial comm: USART0
Port for assert serial comm: None
Enable wake from activity on RX GPIO of application port: False
Enable wake from idle: True
Use USART0 for serial: False (I've tried True and it doesn't make a difference)
Use USART1 for serial: False
Use USART2 for serial: False
Owned by SERIAL_APP
Baud rate: 115200
Flow control mode: USART-based CTS/RTS
and so forth
I am trying to build the CHIP lock-app example by following the instructions of Connect Home over IP (CHIP) Lab, but run into an error at step 7 of Section 3.1 Building the example.
The error is as the attached image, please provide solution for this error, thanks.
During network steering, the scanning completion callback emberAfScanCompleteCallback() always returns a fatal error when trying to scan channel 26 on our custom board (EFR32MG12P332F1024GM48) running the ZigbeeMinimalSoc example project:
Running this same project on the eval kit board 4162A does not return this error:
How can we solve this problem?
For one of my applications, I had generated and Z3Gatwway Host example and an NCP-UART example of SSv4 with the latest EmberZnet 184.108.40.206 for the Zigbee MGM210PA32JIA module.
I had taken the Switch Example provided by SS4 and designed 5 end devices.
I had added 2 end devices to the Z3Gatway Host I was not facing any issue. But when I added all the 5 devices I started observing the following error for every cluster communication:
LINE: ERROR: ezspErrorHandler 0x22
0|app | FLAG VALUE: 0
0|app | LINE: ezsp ver 0x08 stack type 0x02 stack ver. [6.7.8 GA build 373]
0|app | LINE: Ezsp Config: set security level to 0x0005:Success: set
0|app | LINE: Ezsp Config: set address table size to 0x0002:Success: set
0|app | LINE: Ezsp Config: set TC addr cache to 0x0002:Success: set
0|app | LINE: Ezsp Config: set stack profile to 0x0002:Success: set
0|app | LINE: Ezsp Config: set MAC indirect TX timeout to 0x1E00:Success: set
0|app | LINE: Ezsp Config: set max hops to 0x001E:Success: set
0|app | LINE: Ezsp Config: set tx power mode to 0x8000:Success: set
0|app | LINE: Ezsp Config: set supported networks to 0x0001:Success: set
0|app | LINE: Ezsp Value : set end device keep alive support mode to 0x00000003:Success: set
0|app | LINE: Ezsp Policy: set binding modify to "allow for valid endpoints & clusters only":Success: set
0|app | LINE: Ezsp Policy: set message content in msgSent to "return":Success: set
0|app | LINE: Ezsp Value : set maximum incoming transfer size to 0x00000052:Success: set
0|app | LINE: Ezsp Value : set maximum outgoing transfer size to 0x00000052:Success: set
0|app | LINE: Ezsp Config: set binding table size to 0x0010:Success: set
0|app | LINE: Ezsp Config: set key table size to 0x0004:Success: set
0|app | LINE: Ezsp Config: set max end device children to 0x0040:Success: set
0|app | LINE: Ezsp Config: set aps unicast message count to 0x000A:Success: set
0|app | LINE: Ezsp Config: set broadcast table size to 0x000F:Success: set
0|app | LINE: Ezsp Config: set neighbor table size to 0x0010:Success: set
0|app | LINE: NCP supports maxing out packet buffers
0|app | LINE: Ezsp Config: set packet buffers to 72
0|app | LINE: Ezsp Config: set end device poll timeout to 0x0008:Success: set
0|app | LINE: Ezsp Config: set zll group addresses to 0x0000:Success: set
0|app | LINE: Ezsp Config: set zll rssi threshold to 0xFFD8:Success: set
0|app | LINE: Ezsp Config: set transient key timeout to 0x00B4:Success: set
0|app | LINE: Ezsp Endpoint 1 added, profile 0x0104, in clusters: 8, out clusters 19
0|app | LINE: Ezsp Endpoint 242 added, profile 0xA1E0, in clusters: 0, out clusters 1
0|app | LINE: EMBER_NETWORK_UP 0x0000
0|app | LINE: NWK Steering stack status 0x90
and even I am getting 0|app | LINE: ERROR: ezspErrorHandler 0x39 and same the Ember_NETWORK_UP is happing every time.
Is there a solution for this issue.
I am using the EFR32MG12 (BRD 4161 Rev 03) as coordinator.
In the Network with Coordinator i have many different types of 3rd party devices such as SPC Motion sensors( 3 devices), Auara switch button, PIR Motion Sensor, SPC window sensor, SonOFF motion senor, Eria Switch , and sensor Puertas y ve Enlace Zigbee Door and Window sensor.
I want to make 2 Groups of 3rd party devices with coordinator in network.
1. Group-1 i want keep all Motion Detector sensor in a group
2. Group-2 i want to keep all Switches in a group.
how can i achieve this, please let me know, thanking you.
I am about to begin my Zigbee adventures within HA using a newly purchased Conbee2 stick with a couple handfuls of Aqara sensors on their way. I currently run a Hue bridge (HA integration) with about 8 Hue bulbs. I plan to use deCONZ (maybe fallback to ZHA if I run into issues?)
Should I move the Hue bulbs over to the Conbee2 and remove the Hue bridge as my coordinator? My understanding is that Hue bulbs should act as routers to extend the network to the Aqara sensors. SHAREit
I am not well versed in this, but I've read that Hue uses ZLL native bulbs. These fall back to ZHA if used on a non-Hue coordinator. Does this impact me, or my ability to utilize Hue bulbs as routers to the Aqara sensors?
Given potential compatibility issues between Hue & Aqara zigbee devices, would it be preferred for me to run 2 different Zigbee networks on separate non-interfering channels? One for Hue using their hub/coordinator, and the other using the Conbee2 with the Aqara devices? I'd likely have to pick up some routers to extend the Aqara network (couple zigbee plugs or something?).
I don't have any issues with my Hue network currently across 3 floors. In any/all cases, I'd plan to ensure Zigbee channels do not interfere with each other or my 2.4ghz wifi network.
Bonus Question: Any advice on specific instructions to properly passthrough Conbee2 into HA? Running in Docker on a Ubuntu machine.
I have connected the smart door sensor(zigbee) with the WSTK (which acts as coordinator). Device gets announced to the network and IAS Zone notification is also coming over the network as checked in the network analyzer as well.
I want to know the value of device timeout configured in device. How I can check that. Please help me on this.
Hi, I have developed EFR32MG21 on the custom board.
I wants to reach lowest power consumption.
My project have used a pin for gpio interrupt.
GPIO_PinModeSet(UART_RX_INT_PORT, UART_RX_INT_PIN, HAL_GPIO_MODE_INPUT_PULL, HAL_GPIO_DOUT_HIGH); /* Register callbacks before setting up and enabling pin interrupt. */ GPIOINT_CallbackRegister(UART_RX_INT_PIN, NULL); /* Set rising and falling edge interrupts */ GPIO_ExtIntConfig(UART_RX_INT_PORT, UART_RX_INT_PIN, UART_RX_INT_PIN, false, true, true);
I have used this code. The current consumption has been get ~40 uA.
If I have disabled this gpio interrupt, The current consumption has been get ~5 uA.
Is there gpio interrupt of low power?
wee need a cluster Measurement temperature in mode Server and cluster ON/OFF client ?
In seem time . no problemn for configuation cluster Measurement temperature in MENU ZLC cluster .
but impossible to activate cluster ON/OFF client ?